Finished floor level does not take into account any applied finishes as these may be added by owners, occupiers or tenants, will vary in thickness, e.g a thick shag-pile carpet has different thickness to a laminated floor, and may be replaced.
Simply so, What is finished level? Finished levels mean liveable levels, which to be specific are floors of a building that are developed with walls (specifically studs, insulation and drywall), separate rooms (if necessary), adequate ceiling height, electricity, flooring, and are heated areas for all four seasons.
What does above finished floor mean? AFF – Above Finish Floor. This is an acronym commonly used in dimensioning. If you see a note saying 8′-0” AFF, it means that whatever is being referenced is 8 feet and zero inches above the surface of the finished floor (whatever you walk on, e.g. the surface of the tile, not the underlay) in that room.
Subsequently, What is SS level?
This is where all the building element finish levels are referenced from. SFL refers to the level at the top surface of the floor screeding or concrete topping. While SSL refers to the level at the top surface of the structural slab.
What is finished floor height?
The finished floor elevation (FFE) is the height at which the concrete slab for the 1st floor living area of the home needs to be at based on Florida Emergency Management Agency (FEMA) and specific land development code requirements.
What is the difference between FFL and SSL? Correct me if Iam wrong, FFL refers to the level at the top surface of floor finish. This is where all the building element finish levels are referenced from. SFL refers to the level at the top surface of the floor screeding or concrete topping. While SSL refers to the level at the top surface of the structural slab.
What is FFL in floor plan?
A finished floor level survey measures where the height of the floor will be in a new building.
What does FFF mean in construction? Form-Fit-Function (FFF) Definition and Rules.
What does FF mean on blueprints?
Also referred to as FF is Finished Floor Elevation. The term FFE refers to the top of the structural slab and its elevation above sea level.
What does WC mean in a house plan? Window – Basix window number. WB. Weatherboard. WC. Water closet.
What is CB in home?
CB is labeling closet spaces.
What is CB in house drawing? C.B. – Catch Basin. C.D. – Construction document. CEM. – Cement. C.F.M. – Cubic Feet per Minute.
What does WP mean in structural drawings?
Structural Abbreviations
| ASD | Allowable Stress Design |
|---|---|
| VOF | Vertical Outside Face |
| WWF | Welded Wire Fabric |
| W/ | With |
| WP | Working Point |
• Jan 16, 2020
What is FFL level?
Finished floor level (FFL) refers to the uppermost surface of a floor once construction has been completed but before any finishes have been applied.
How thick is the floor? The floor of one level of a home shares framing with the ceiling of the level below it. In a typical home, the entire structure between levels can be about 12 to 14 inches thick, depending on the type of joists used and the finish materials for the floor and ceiling.
What is GL in engineering drawing?
GL. ground line or ground level. GP. ground plane.
What is finished ground level?
The finished ground level would be the profile of the post-construction ground after any backfill is complete. These values could also be contoured on plan views.
What does SIM mean on construction drawings? Architectural Abbreviations
| RBR | Rubber |
|---|---|
| RM | Room |
| SIM | Similar |
| SD | Smoke Detector |
| SPEC | Specified OR Specification |
• Aug 17, 2020
What does finished floor mean?
A finish floor (also known as floor covering) is the top layer of flooring. In other words, it is the layer that you walk on, and it is typically quite decorative layer compared to the layers of flooring beneath it.
What does CA stand for in construction? CA/ Construction Administration: If you’re mailing a letter, it may stand for The Golden State, but in architecture, CA means Construction Administration or Contract Administration. CA refers to the architectural phase and architect’s duties during the construction of your project.
What does FIR mean in construction?
FIR
| Acronym | Definition |
|---|---|
| FIR | Facility Inspection Report |
| FIR | Full Inspection Report |
| FIR | Financial Inventory Report |
| FIR | Federal Industry and Research (type of grant) |
What does TOC stand for in civil engineering? T.O.C.: Top of Curb or Top of Concrete.
Don’t forget to share this post !