How do I set an ASA username and password?

To set the enable password on your Cisco ASA 5505:

1. Get into the command line. I prefer using the console cable to directly connect.
2. Hit enter a few times to get the prompt.
3. Type ‘ena’ to enter enable mode.
4. Type ‘config t’ .
5. Type ‘enable password PaSsWoRd’ , replacing the second, ‘PaSsWoRd’ with desired password.

Likewise, What is the default Cisco ASA password?

By default, the password is blank, and you can press the Enter key to continue.

Also, How do I reset my ASA 5505 password?

Reset Password in Cisco ASA Firewall

1. Step 1: Login to Cisco ASA device with console cable and reboot the device. …
2. Step 2: Press ‘ESC’ key or ‘BREAK’ key on the keyboard to break the boot process. …
3. Step 3: Now, here is the trick. …
4. Step 4: Reboot the device. …
5. Step 5: When the ASA is booted, it will not ask for password.

Secondly, How do I reset my ASA password?

To recover passwords for the ASA, perform the following steps:

1. Step 1 Connect to the ASA console port according to the instructions in « Accessing the Command-Line Interface » section.
2. Step 2 Power off the ASA, and then power it on.
3. Step 3 After startup, press the Escape key when you are prompted to enter ROMMON mode.

Furthermore How do I reset my Cisco ASA to factory settings? Solution

1. Connect to the ASA via the console Cable. …
2. log in and go to configure terminal mode.
3. Execute the following command “config factory-default”
4. Press the space bar a few times to execute the commands.

How do I log into cisco ASA?

ASDM Web Access Guide:

1. On the PC connected to the ASA, launch a web browser. (Verify that Java and JavaScript are enabled in your web browser)
2. In the Address field, enter the following (default) URL: https://192.168.1.1/admin.
3. Run Startup Wizard.

How do I reset my cisco ASA password?

Reset Password in Cisco ASA Firewall

1. Step 1: Login to Cisco ASA device with console cable and reboot the device. …
2. Step 2: Press ‘ESC’ key or ‘BREAK’ key on the keyboard to break the boot process. …
3. Step 3: Now, here is the trick. …
4. Step 4: Reboot the device. …
5. Step 5: When the ASA is booted, it will not ask for password.

How do I configure my ASA 5505 firewall?

Cisco ASA 5505 configuration

1. Step1: Configure the internal interface vlan. …
2. Step 2: Configure the external interface vlan (connected to Internet) …
3. Step 3: Assign Ethernet 0/0 to Vlan 2. …
4. Step 4: Enable the rest interfaces with no shut. …
5. Step 5: Configure PAT on the outside interface. …
6. Step 6: Configure default route. …
7. 11 comments.

How do I enable ASDM in ASA?

On your laptop, open a browser and go to https://192.168.1.1/admin to get to the Cisco ASDM page. Accept the certificate error and continue to the webpage. The last step is to click Install ASDM Launcher and Run ASDM from the webpage. The installer will then run through the process of installing.

How do I reset my ASA 5510?

1. Connect your console cable and make sure you can see the command prompt for the ASA – even if you can’t log in. …
2. Power cycle the appliance – flick the power switch on the front off and on again.
3. Watch the boot progress, and when prompted, press Esc to interrupt the boot and enter ROM Monitor mode.

What is Rommon mode in Cisco router?

The ROM Monitor (ROMMON) is a bootstrap program that initializes the hardware and boots the Cisco IOS XE software when you power on or reload a router. If your router does not find a valid system image to load when it is booting, the system enters the ROMMON mode.

How do I reset my ASA 5505 to factory settings?

1. After you open connection, press enter a couple of times, and you should get a prompt like: ‘ciscoasa>’
2. type ‘enable’ to go to enable mode. …
3. type ‘config t’
4. type ‘config factory-default’
5. hit spacebar when the ‘more’ is displayed. …
6. type ‘reload save-config noconfirm’

How do I wipe my ASA 5505?

1. After you open connection, press enter a couple of times, and you should get a prompt like: ‘ciscoasa>’
2. type ‘enable’ to go to enable mode. …
3. type ‘config t’
4. type ‘config factory-default’
5. hit spacebar when the ‘more’ is displayed. …
6. type ‘reload save-config noconfirm’

How do I reset my ASA 5520 to factory settings?

1. After you open your connection, press enter a couple times, and you should get a prompt like: ‘ciscoasa>’, or ‘hostname>’
2. Type ‘en’ to go to enable mode. …
3. Type ‘config t’
4. Type ‘config factory-default’
5. Hit spacebar when the ‘more’ thing happens. …
6. Type ‘wr mem’ to save the new config.
7. Type ‘reload’

How do I save ASA configuration?

Save running config on Cisco device

Use the command copy running-config startup-config (copy run start) to overwrite the current startup config file with what is currently in the running configuration file.

How do I access ASA through ASDM?

Open the shortcut and fill in the IP address (192.168. 1.1), leave the username blank and put in the password firewall. The ASDM will then connect to the ASA and load the java interface. You can now configure the ASA as per your requirements.

How do I know if ASDM is installed on ASA?

Commands: show run http [check if http server is enabled, and http access is allowed on the interface you are trying to access.] show run asdm [check that an asdm image is mentioned, and the version is compatible with the ASA image version.] show flash [check that the asdm image mentioned is present in the flash.]

How do I open ASDM in browser?

How to run Cisco ASDM as a Java Web Start application

1. go to the Cisco web console (in my case the url was https:/192.168. 1.1/admin).
2. retrieve the jnlp (Java Network Launch Protocol ) file (in my case the file name was asdm. jnlp)
3. execute jnlp file to start the ASDM application.

How do I restore ASA from Rommon mode?

To recover passwords for the ASA, perform the following steps:

1. Step 1 Connect to the ASA console port according to the instructions in « Accessing the Command-Line Interface » section.
2. Step 2 Power off the ASA, and then power it on.
3. Step 3 After startup, press the Escape key when you are prompted to enter ROMMON mode.

What is the default cisco username and password?

Most routers and switches by Cisco have default passwords of admin or cisco, and default IP addresses of 192.168. 1.1 or 192.168. 1.254.

How do I enable ASDM in ASA?

Copy the downloaded ASDM image file to your firewall using TFTP:

1. Configure ASA to load ASDM at next reboot using the asdm image flash:ASDM FILENAME command:
2. Enable the http server and identify the management station that will be used to configure the appliance:
3. Create a user on the device:

How do I access ASDM ASA?

On your laptop, open a browser and go to https://192.168.1.1/admin to get to the Cisco ASDM page. Accept the certificate error and continue to the webpage. The last step is to click Install ASDM Launcher and Run ASDM from the webpage. The installer will then run through the process of installing.

Is Cisco ASA 5505 a router?

Note: If you purchase Cisco ASA 5505, please verify the package contents. The ASA is NOT a router, though and while you can do things on the ASA that can make it act something like a router it is important to understand the differences between true routing and what the ASA actually does.

What is Nameif on ASA?

The nameif command is used to specify a name for the interface, unlike the description command the name of your interface is actually used in many commands so pick something useful. As you can see the ASA recognizes INSIDE, OUTSIDE and DMZ names. It uses a default security level of 100 for INSIDE and 0 for OUTSIDE/DMZ.

Don’t forget to share this post on Facebook and Twitter !